How to make a necklace ?

How to make a necklace?

There are many reasons for creating a necklace. Maybe because it is interesting. Because you can not only play your own creativity. And you can create something completely unique to reflect your personal style. In addition, making a necklace is very easy. You may wish to look down:

Step 1: Collect the materials you need for your necklace.

Make sure all materials are ready: beads, beaded lines. And wire cutters, crimp beads, super glue and seals. In order to properly organize the necklace.
The wire is preferably a flexible crimp line and a crimp line.
All of these materials can be purchased at your local handicraft store.

How to make a necklace

Step 2: Determine your necklace style.

When considering which type of necklace to make. Please consider factors such as length. If you like a shorter necklace. Then consider making a collar or necklace. If you like longer necklaces. You may need a lasso (longer, usually on the chest) necklace.
You can also make up your own style and length. These simple suggestions will give you a general idea.
Please note that the finished length of the beaded necklace includes the length of the beads you have used and the length of the selected jewelry buckle.

Step 3: Choose a suitable length. Short necklace, about 13 inches in length.

A little longer, it drops to about 14 to 16 inches. The Lariat is the longest, about 45 inches or more. As mentioned above, you can also choose your own length and style

 Choose a suitable length

Step 4: Measure your neck and determine the length.

Pick up the tape and look at yourself in the mirror. Wrap it around your neck. Try small loops and big loops to see what you like. This will give you an idea of the look of the necklace around your neck.

Step 4: Measure your neck and determine the length

Ready to design and layout?

Step 1: Arrange your beads on a flat surface.

For example, above the table. Filter the beads until you find your favorite design. Try using different color beads. You might even want to go to a multi-layered bead string. Or you might want a collar that can be wrapped around your neck a few times. It is also a long ring.

Ready to design and layout

Step 2: Place the bead on a flat surface.

Because the bead board is a tool. Therefore, the beads can be threaded in a large place. And quickly improve your design skills. You can use it to measure the length of the necklace. Also fix the beads in place. If you plan to make necklaces on a regular or even irregular basis. A wooden board should be prepared.
Place your beads in the number zero in the design of your choice. Use the side numbers and dashes to measure the length of the necklace.
Use the channel to arrange the beads.
Tray illustrations are used to secure beads and discoveries.

Place the bead on a flat surface

Step 3: Cut the determined length of the bead line.

Plus 6 inches. For example, you want to make a necklace. Then cut a total of 22 inches of thread (16 inches plus 6 inches).

Cut the determined length of the bead line.

Step 4: Collect 2 crimp beads.

1 button and the required necklace beads

Making a beaded necklace:

Step 1: Slide a small ball onto the strings.

Then, slide the crimp beads into. Press down again about 1 inch (2.5 cm). Remember that you have not yet transferred your design to the thread. These are essential initial steps. And make sure your necklace is safe.

Step 1 Slide a small ball onto the strings.

Step 2: Place one end of the buckle (jumping ring) on the crimping beads.

Then, make a loop with the threading material.

Place one end of the buckle (jumping ring) on the crimping beads.

Step 3: Pass the end of the threading material through the buckle portion.

Then add the “bead-crimp-bead” combination. Use a crimping tool / needle nose pliers to crimp it into place.If using a bead line. You can put a little glue on either end. To ensure that the beads and crimps remain the same. ). These steps will prevent the wire material from rubbing at both ends of the bead. This causes the necklace to break.

Pass the end of the threading material through the buckle portion

Step 4: Slide your design onto the string.

After being satisfied with the design. Please carefully remove one bead at a time. Then string it on the thread. Make sure to leave approximately 3-4 inches (7.5-10 cm) of wire material at the end.
The beads are threaded onto the threading material. Until there is nothing on the bead board.

Slide your design onto the string

Step 5: Use a buckle/hop ring and a bead-crimp-bead combination.

Try pushing the remaining pull material into the bead hole below the pressure strip.
Be careful not to pull the cable material too tightly. Leave a little slack on the necklace, about 2-4 mm or 1/4 inch. This leaves space for the bead to move and rotate. So they don’t rub each other or thread too much material. If the threading material is too tight, the necklace will harden. This will make the design look angular. Instead of a slight round like a necklace.

Step 6: Crimp the second end.

Then use a slush knife to cut the cable material. It is not recommended that you cut the wire too close to the crimp beads. A 1 inch (2.5 cm) wire is carefully hidden in the bead hole. It is a good guarantee to prevent breakage.

Crimp the second end

Finished necklace:

Finished necklace

No comments to show.

Leave a Comment